Power Factor Correction: An Overlooked but Powerful Tool for Delivering Energy Efficiency and Savings

Power Factor Correction

 

 

 

 

June 23 2016

Joy Silber
Amid all the talk about how to reduce CO2 emissions and limit climate change, renewable energy sources such as wind and solar often take centre stage. But there’s another technology poised to deliver energy reductions of 10% or more that gets far less attention: power factor correction (PFC).
If you’re not familiar with PFC, you are far from alone. To date, it’s been a largely overlooked method of reducing energy consumption, costs and CO2emissions, and achieving sustainability. But PFC is actually far more effective than many “green” alternatives because it effectively enables companies to get more power out of the same amount of utility electricity.

Understanding power factor
I won’t kid you: PFC is a bit complicated to explain and understand, making a full discussion of it beyond the scope of this post. You can learn all about it from this free Schneider Electric paper titled Energy efficiency improvement through optimization of the power factor correction.
But the basic concept is it takes more energy to power a given load than the actual power that the load consumes. That’s because some of the energy is lost in translation, so to speak. Power factor is used to determine just how much more energy will be required to power the load. This amount is measured by calculating a ratio that shows how efficient any given machine is. A motor with a power factor of .90, for example, is 90% efficient. To determine how much energy you’ll need in kVA to power that machine, you perform an equation: 100 (for a 100kW motor) ÷ 0.90 = 111kVA. So you’ll need 111kVA of utility power to run that 100kW motor.

Saving energy with power factor correction
Obviously, the lower your power factor of a given piece of equipment, the less efficient it’s going to run. And that inefficiency can cost you more than just a higher utility bill because in some areas, you’ll get penalized for consuming more power than your contract allows, taking into account your power factor.
The key to ensuring that doesn’t happen is to use a capacitor bank or energy compensator. These systems perform PFC to help reduce the amount of power an AC device has to consume to generate its rated amount of power. Some systems, such as Schneider Electric’s VarSet low-voltage capacitor banks, automatically correct power factor. This results in a power factor close to 1, meaning virtually no power is wasted.

Using PFC systems can deliver a number of benefits, including:
• significant savings on electricity bills, with ROI typically within two years (actual savings vary depending on local utility penalties)
• improved energy efficiency
• attained sustainability goals
• reduced energy use waste
• increased available power at your facility
• reduced carbon footprint
• Improved equipment reliability and lifespan by filtering “dirty power”

Sounds an awful lot like many of the same benefits that solar and wind deliver, doesn’t it? The savings can indeed be impressive, and they’re relatively simple to achieve. To learn more about power factor correction in your facility, email:powersolutions@schneider-electric.com

Joy Silber is the Strategic Marketing & Sales Optimization Manager of Power Solutions at Schneider Electric. With experience across multiple industries: Food and Beverage, Mechanical, Agriculture and Power Transmission, Joy has held previous roles in National Sales Development, Market Segment Management, Marketing Services Management and Business Development. She has a B.S. from North Carolina State University and is an active volunteer in her community. This article was first published as a blog

 

Related Articles


Latest Articles

  • The Inaugural EFC Award of Excellence Presented to Keith Rodel, Hubbell Canada

    The Inaugural EFC Award of Excellence Presented to Keith Rodel, Hubbell Canada

    November 29, 2022 On November 10, 2022, Keith Rodel, from Hubbell Canada, was presented with the first EFC Award of Excellence. This award is a peer recognition to a retired member of the Electro-Federation of Canada who has made an outstanding contribution to the industry in standards and regulations. Hubbell Canada’s Frank Magisano, Director of… Read More…

  • New Report Explores Proven Practices for Building a Circular Economy in Canada

    New Report Explores Proven Practices for Building a Circular Economy in Canada

    November 29, 2022 Canada ranks among the top waste-producing countries around the world.By 2050, annual global waste generation is projected to grow by 70 per cent and consumption demands are estimated to require the resources of three Earths. CSA Public Policy Centre‘s new report, Rounding the Corner: Towards a Circular Economy in Canada, highlights how transitioning to… Read More…

  • Agents of Change: Bridging the Gap Between Talk and Action

    Agents of Change: Bridging the Gap Between Talk and Action

    This article is a summary of EHRC’s Agents of Change panel, Bridging the Gap Between Talk and Action. The annual event hosted by EHRC at the Toronto Reference Library is a two-day event designed to promote diversity, equity, and inclusion in the electricity industry. Read More…

  • Recap from EFC’s12th Annual Future Forum

    Recap from EFC’s12th Annual Future Forum

    November 25, 2022 On November 17, 2022, Electro-Federation Canada (EFC) virtually organized the 12th Annual Future Forum themed “Innovation During Disruptive Times: Finding the crossroads between talent and technology,” together with the 9th Annual Marketing Awards Presentation: Celebrating Innovation Excellence. This year, over 100 members experienced a reformatted program that brought together marketing and supply… Read More…


Changing Scene

  • IBEW President Lonnie R. Stephenson Retires, Kenneth W. Cooper Named New President

    IBEW President Lonnie R. Stephenson Retires, Kenneth W. Cooper Named New President

    November 29, 2022 International Brotherhood of Electrical Workers President Lonnie R. Stephenson is retiring, effective Jan. 4, bringing an end to a nearly five-decade active career in the union. “It’s been the honor of my life to serve the members of the greatest union in the world and advance the cause of trade unionism in… Read More…

  • Eddy Group Announce Branch Manage for New Charlottetown Branch

    Eddy Group Announce Branch Manage for New Charlottetown Branch

    November 25, 2022 Eddy Group Limited has announced Emily VanToever as the Branch Manager at their new location in Charlottetown, PEI, which is scheduled to open in early 2023. Emily begins her new position on Monday, November 21, 2022, and will report to Richard Barker, Corporate Sales Manager. “Emily comes to Eddy Group Ltd. from… Read More…

  • IDEAL Virtual Electrician Experience

    IDEAL Virtual Electrician Experience

    November 25, 2022 The IDEAL Virtual Electrician Experience (IVEE) is a free interactive virtual reality app that’s perfect for people who want to learn more about the electrical industry. The app for Oculous Meta Quest 2 headsets gives you a virtual, hands-on look at what it takes to be an electrician. Go HERE for more information Read More…

  • BJ Electric Supplies Announces Retirement of Kevin Gutsch

    BJ Electric Supplies Announces Retirement of Kevin Gutsch

    November 25, 2022 BJ Electric Supplies has announced the retirement of a member of its executive team, Kevin Gutsch, Vice-President of Operations, on or before November 30th, 2022. “Kevin began his career with BJ Electric Supplies on November 20, 1979. His first position was picking orders as a warehouse worker. After enthusiastically taking on whatever… Read More…