Canadian Electrical Industry News Week

Dec 8, 2020

HorticultureBy Lynn Belken and Katy McSurdy

In Part 1 of this interview with Leora Radetsky, we covered smart lighting, customizability, and COVID-19 possibilities. For Part 2 we are diving into indoor agriculture, how utilities are helping drive LED adoption with incentives, and challenges in the LED market. 

KM: What can you tell us about indoor agriculture and LEDs?

LR: This is an area I am very excited about. We’re seeing more and more square footage devoted to growing products indoors. One of the most important things to realize about CEA is that the light levels needed for plants are much higher than the light levels for people — 10 or even 100 times higher. With those higher light levels, you have concern from growers, utilities, EE programs, and states about how much energy is being used. 

LED products provide not only the ability to save more energy than incumbent systems, but also a different choice of light spectra so that growers can optimize their plant growth and products. For some products, using a certain spectrum (colour) of LED can improve the growth cycle and shorten the growing time. A shorter growing time results in more crops on the market and an increased profit. Light for plants is food and nutrients. If you dim the light source to save on energy, you can harm the plants and the grower’s profit.

LEDs can also last longer than HPS and metal halide light sources, which equals improved maintenance costs and operational costs for growers because they are replacing less often. Now we are seeing LED products that can produce more light than the best performing HPS. So if you have crops that need a lot of light (like cannabis), not only can you replace LED for HPS on a 1:1 basis, you may be able to have 1 LED for 2 HPS fixtures. Saving growers even more money. 

One of the benefits of LEDs is the way they produce heat. Yes, they still produce heat, but they are more energy efficient so they are not producing as much heat and because they are not directly radiating the crop, they are not damaging them with too much heat. In many cases, you can even put the LEDs closer to the crop canopy, which means you can have a lower wattage light (saving growers energy), but still provide the same amount of light to the crops. There are a lot of regulations popping up for CEA related to maximum lighting power density or minimum efficacy. Even though the maximum lighting power density is much higher for CEA than commercial lighting, it is oftentimes still not enough light for some crops. That’s where LEDs can help — they are more efficacious and growers can pick the light level that they need to be profitable.

KM: Are farmers finding that indoor agriculture is more profitable?

If you can grow in a greenhouse and you have a lot of daylight in the greenhouse, it is more profitable because you can use natural light. But part of what farmers get in a greenhouse is affected by the glazing on the glass. The glazing used on the glass might cut off UV light and some cases the UV light is beneficial for plants and they won’t get that because of the glass. Glass also lets in heat and the farmer then needs to vent/open up the greenhouse to control the heat. The effect of too much heat is that it can dry out the plants, dry out the soil, you have to water more, etc. It comes down to balance. 

But what is interesting about lighting and plants grown in indoor facilities, is that the plants currently being grown in greenhouses/indoor facilities have developed under sunlight, which is a very broad type of light. There are some initiatives happening to develop different strains of plants/cultivars (like lettuce) that are developed to be more effective at growing under LEDs. Just like developing other cultivars — sweet smelling roses, roses with multiple blooms — genetics are helping us grow crops more effectively indoors. Genetics of the plants is key, we have more people on the planet, we have climate change which is making it harder to grow crops outdoors. There’s catastrophic flooding and drought events, pests that are adapting to weather changes, and diseases that are becoming resistant to chemicals that are used. If we can look at lighting and genetics together, I think that’s the way we are going to grow the food we need for people. 

KM: What role have utilities and energy programs played in the adoption of LEDs?

LR: They’ve played a really large role in market transformation. First and foremost, the incentives they provide buy down the cost and help make the products more affordable. They also help prove the products are viable — if they use an Energy Star threshold or DLC specification, they are setting a threshold for minimum product performance. Incentives help to drive baselines higher so that LED technology becomes the norm. By focusing on quality as well as cost and energy savings, the lighting will meet the customer’s expectations. There are a lot of products in the market, so taking a little care up front will go a long way to satisfaction. 

KM: In residential applications, consumers have concerns about choosing the right brand, dimming features, etc. Do C&I customers have these same concerns? What should they do about buzzing or humming from LEDs in that setting?

LR: There is still some of that concern, especially in retrofit vs. new construction. You want to make sure that you don’t have compatibility issues; most of these concerns have to do with interoperability (i.e. is the dimmer compatible with the light source and is the light source compatible with the dimmer?). Look at spec sheets and talk to the manufacturer to ensure compatibility is important. If you have a product that is specified and another product is substituted due to cost during the bidding process, you could end up with compatibility issues that haven’t been addressed. Make sure that specifications are mentioned and look at requirements for dimming and other compatibility features. In commercial lighting there is a different value chain with many more choices of controls and lighting and support from representatives and distributors, since you are not just shopping at a big box or hardware store. Buzzing and humming can be a sign of a compatibility problem between the control system and the luminaire. Or, it might be from the controller/hub; and in those cases you need to remote that hub or peripheral components to make sure they are not audible to occupants. 

KM: What are some of the challenges that LEDs have been facing in the market?

LR: The accuracy of lifetime claims is important. LEDs can last a long time, but if they are no longer producing enough light or if the colour is shifting, that is a problem for people. Even though they are not failing immediately, they may last a long time but that is not always good enough. As an industry we need to understand this better and understand when it is time to replace. Serviceability is starting to be addressed, but there is room to improve. What components are serviceable? How easy is it to service/swap parts? Do you have enough information to buy a new one to match if you need a certain colour? Or do you replace all, so that the products match? Along with that, comes sustainability — how can we recycle and produce sustainable products over a long period of time so that we are not producing a lot of waste stream products?

KM: Anything else you feel is important that we share? 

LR: I don’t think that you can have a silver bullet or one product that will be best for every application. I really think that people should do their due diligence by validating performance claims and warranty language, and verifying the service that the manufacturer and installer offer. Lighting is a long-term investment — you want to pick a good product. Lighting design professionals are helpful and important to help customers find good quality products, and to help customers understand the limitations and characteristics of those products. In the end the customer needs to be comfortable with the investment, so it’s important to validate the claims and know what you are buying. 

KM: Thanks so much for a fascinating interview on LEDs. I learned a ton! I had no idea customizable lighting was within reach and that plant cultivars are being created around LEDs. I’m excited and hopeful for the future of lighting and energy efficiency. Thanks for sharing your time with us. 


To learn more about LEDs, check out Part 1 of this interview.

Lynn Belken is A Senior Marketing Account Representative for Nexant. Katy McSurdy is a Content Marketing Strategist, also with Nexant. This article was first published as a Nexant blog.

Photo source: Philips Lighting

Changing Scene

  • Prev
MP Scott Duvall has introduced an amendment to the Income Tax Act regarding travel expenses for ...
George Brown College has partnered with Hilti (Canada) Corporation to help women build rewarding ...
Signify and the National Hockey League (NHL) has announced a partnership to help the more ...
Join the Electricity Distributors Association (EDA) on March 23 for a virtual session during which ...
ABB is hosting a Smart Building thought leadership session with six webinars presented by industry ...


 

www.liteline.com

 

 

 

 


 

Canadian Electrical Contractor Discussion Group: Can You Count the Deficiencies?

EIN CECD 400Have you ever been called to fix the work of a 'handyman'?

"Was supposedly done by a"certified ' electrician....told the homeowner that he got a $266 permit....no record at TSBC. Can you count the deficiencies?"

"There is a second panel change in the triplex also.......even more deficiencies. Think the guy was a glorified handyman. Ones not obvious: 240 BB heat hooked up 120....drier on 2p20....range on 2p50....water heater fed with 2c14 Bx on 2p15."

Go HERE to join the discussion

 


 

Surgelogic RecallProduct: Surgelogic™ NQ SurgeLoc™ Surge Protection Device.

Issue: The Surgeloc Surge Protection Device can experience an arc event, which can result in a fire hazard.

What to do: Consumers should immediately stop using the recalled surge protection devices and contact Schneider Electric for instructions on receiving a free equivalent replacement surge protector.

 

 

Read More


 



Terry BeckerBy Terry Becker, P.Eng., CESCP, IEEE Senior Member

The electric shock hazard has been neglected.  Journeyman Electricians have accepted been shocked as part of the job, a “right” of passage, a badge of honour. 

This has not been acceptable and Journeyman Electricians may not be aware of the long term sequela health effects of receiving multiple low voltage electrical shocks and how it may have impacted them.  With respect to treatment there is only a single formal recognized treatment centre in Canada, the St Johns Rehab Centre. Electrical Injury Program.

Read More


 

EIN Code Quiz 2Take this opportunity to test your knowledge of the Canadian Electrical Code - Part 1. Here are two questions on essential electrical systems: health care. 

You'll find the answers in EIN articles written by our code experts — mainly Bill Burr and Terry Becker — and of course in your own best practices. Answers will be posted on our website in a few days and published in our next issue. Good luck and share your results with our Facebook group: Canadian Electrical Contractor Discussions.

 

 

Read More


 

Product News

  • Prev
Individually tested to 10,000 volts AC and rated to 1,000 volts AC for safety and peace of mind. ...
The VS-AVT-C08-L10 VeriSafe Absence of Voltage Tester is the first-of-its-kind voltage tester that ...
HPS Drive Isolation Transformers, are designed to meet the rugged demands of both AC and DC ...
Plug-and-Play Gimbal System for the DJI Matrice 200 Series and Matrice 300 Offers High-Definition ...
MaxLite has announced the launch of c-Max Lighting Controls, a patent pending design that makes it ...
Klein Tools, for professionals since 1857, introduces a new line of conduit benders, available in ...
Any time an electrician or technician makes a voltage measurement on a live conductor, there is a ...
Autodesk, Inc. has announced the worldwide availability of Autodesk Takeoff, a new product ...
Autodesk, Inc. has announced Autodesk Build™, a new project and field management ...
The eLumigen High CRI C1D2 LED Fixture is the ideal light source replacement for Paint Booth, ...

 

Extech Non-Contact High Voltage DetectorFLIR Systems has announced the availability of the Extech DV690 its first non-contact high voltage detector with a detection range of up to 69,000 volts (69 kV). The industrial-grade DV690 provides early warning alerts of energized electrical components for utility lineworkers, telecommunications installers, first responders, search and rescue teams, and tree removal services.

The DV690 features five flexible mounting options: handheld, around the neck, clipped to a belt, strapped to an arm, or attached to a universal spline hot stick. The three handsfree possibilities allow the most optimal operation to efficiently and carefully complete a job. Using a hot stick creates a safer distance to target, extending operator reach.

Read More


 

 

Milwaukee Radius Compact Site LightThe M18 RADIUS Compact Site Light with Flood Mode provides a two-in-one solution for area and task lighting with less to carry. The compact LED light delivers 2,200 lumens in area mode and 1,000 lumens in flood mode. The light offers up to 16 hours of run-time with the option to be plugged in using the AC inlet for extended run-time.

Its compact size allows you to take this site light on and off the jobsite effortlessly and its 4-1/4" metal hanging hook allows you to easily hang the light overhead. The durable light is equipped with a high impact polycarbonate lens to withstand harsh jobsite abuse. The LEDs never need to be replaced and are backed by a limited lifetime warranty. 

Read More


 

 

Panel PC1200With the Panel PC 1200, B&R introduces a compact and cost-effective all-in-one PC. Equipped with the latest Intel Atom processors and up to 256 GB of mass storage, the Panel PC 1200 is ideal for running HMI applications under Windows or Linux operating systems.

With 2x Gigabit Ethernet and 2x USB 3.0, the Panel PC 1200 is ready for integration into any machine network. Compact CFast cards are used for data storage.

 

 

 

Read More


 

Peers & Profiles

  • Prev
Like most major events over the last year, the COVID-19 pandemic put serious restrictions on the ...
This past December Jennifer Green was honoured with Canada’s Most Powerful Women Top 100 Award for ...
“It was quite surprising,” said Stephanie Smith of being named EHRC’s Leader of the Year. ...
As an advanced networked lighting controls company serving the industrial and large commercial ...
Trilliant, an international provider of utility solutions for advanced metering and smart grid ...
For more than a century, ABB has been investing in Canadian technologies and products to support ...
Mackenzie Gillan, a bright young lady from Baysville, Ontario, tells us about how she learned ...
Energy Efficient Lighting is a LED lighting manufacturer with nearly 30 years of industry ...
Dee Durant is an industrial electrician apprentice attending Conestoga College and an Ambassador ...
ECAO recently launched a new program called Future Leaders Advisory Council (FLAC). Their inaugural ...


EIN Green 100 400

By Blake Marchand

This past December Jennifer Green was honoured with Canada’s Most Powerful Women Top 100 Award for the Skilled Trades category by WXN (Women’s Executive Network).

“It is truly an honour to be recognized by WXN and to be among this group of amazing women,” said Green of earning the distinction. “Throughout my career, I’ve worked with many great mentors and team members – to them, I say thank you for always inspiring me. I am absolutely thrilled.” Green is an industrial mechanic millwright by trade and works with Skills Ontario as Director of Competitions and Young Women’s Initiatives. 

Read More


 

Jo Istanbul Four Seasons ABy Owen Hurst

Recently, Electrical Industry Canada has developed a relationship with Women in Renewable Energy (WiRE), a non-for-profit group developing resources and networking potential for women and all working or planning to work within the renewable energy sector. Aside from being the WiRE President & CEO, Joanna Osawe is the Global Business Development Manager of Major Projects for DMC Power Inc.

EIN sat down with Osawe to learn more about WiRE and the substantial benefits it provides. Joanna is very personable and open regarding her career and her ambition, as well as the opportunities she is developing for women nationally and globally. 

Read More


 

Stephanie SmithBy Blake Marchand

“It was quite surprising,” said Stephanie Smith of being named EHRC’s Leader of the Year. “Leadership in 2020 has certainly been a challenge for everybody in the world let alone the nuclear industry or the electricity industry.”

An engineer by trade, Smith spent the majority of her career with Ontario Power Generation (OPG). She was the first woman to be certified by the Canadian Nuclear Safety Commission at the Pickering Nuclear Generating Station where she served as Plant Manager and was recently named the first President and CEO of CANDU Owners Group. Smith is also a passionate advocate for diversity and inclusion.

Read More


 

Copper $US Dollar price per pound

Kerrwil Publications Great Place to Work. Certified December 2019 - December 2020

538 Elizabeth Street, Midland,Ontario, Canada L4R2A3 +1 705 527 7666
©2021 All rights reserved

Use of this Site constitutes acceptance of our Privacy Policy (effective 1.1.2016)
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Kerrwil