Stainless Steel: Understanding and Identifying the Ideal Enclosure Material, Part 2

May 10 2016

Part 1 of this 2-part series looked at eight different grades of stainless steel, which has become the standard material choice in many industries. It is available in many grades or formulations to accommodate diverse application requirements. Here in Part 2: a cost comparison between stainless and mild steel, available surface finishes, manufacturing processes, and a comparison to plastic and composite enclosures.

Cost comparison

Stainless steel is significantly more expensive than mild steel; Type 304 is roughly four times more expensive than mild steel while Type 316 is roughly five times more expensive than mild steel. Additionally, the manufacturing process is more time consuming than mild steel, which increases production costs as well.

Surface finish

Stainless steel can be purchased in a variety of surface finishes, including:

• #1 — mill finish, a rough and dull finish
• #2D — annealed, pickled, dull cold rolled
• #2B — annealed, pickled, as rolled, cold rolled
• #3 — intermediate polished, applications include consumer products such as sinks
• #4 — standard polish, food and pharmaceutical grade

A stainless steel finish between a #3 and #4 finish has a protective masking applied to one side, which is left on the outside of an enclosure and will be removed as late in the manufacturing process as possible.

Surface finish does have an effect on corrosion resistance. Finer or more polished finishes have increased corrosion resistance, compared to coarser finishes such as 2B or mill finish.

Manufacturing

In general, manufacturing with stainless steel requires additional time and special care. Stainless steel products are usually left unpainted; therefore, special care needs to be taken to avoid scratches and blemishes. For example, to protect enclosures, a masking can be used on the outside surface to protect against scratches through the production process.

Stainless steel also has a grain direction that is visible on polished surfaces. Weldments should be laid out with the grain direction in the same orientation. The grain direction also affects corrosion resistance, as moisture moves parallel to the grain direction easier than across the grain. Enclosures should be designed to feature a vertical grain direction.

  • Welding — the core welding process is essentially the same for stainless steel and mild steel. However, there are differences in the weld wire, gaps, additional blending and bluffing. The weld material needs to match the “host” material; thus, stainless requires additional consumables (types 304 and 316 wire for MiG welding). Other design considerations, such as weld gaps, should also be taken into account. Stainless steel is more challenging to weld and requires a higher level of craftsmanship to create an aesthetic look. These welds also require grinding, blending and buffing to give the weld an acceptable appearance; typically only grinding is required on mild steel welds. Since stainless steel enclosures are largely unpainted, these additional steps are required to hide weld imperfections. The welded joint is a common location to first notice corrosion. During welding, there may be iron particles present, which are embedded into the weld, especially if both mild steel and stainless are welded in the same facility. A process called passivation can be used to clean and re-establish the protective oxide film around the weld area. Passivation is generally done using an acid bath in which the material is dipped. There are also gels that can be applied locally to welds.
  • Forming stainless steel uses the same process as mild steel. However, stainless steel can present additional forming challenges, as it tends to spring back more than mild steel.
  • Painting — some stainless steel enclosures are painted, especially in outdoor environments where solar radiation is a concern. A painted stainless steel enclosure (light color) remains up to ten degrees cooler than an unpainted enclosure in direct sunlight. Paint also offers an additional level of protection against corrosion in extreme environments. Stainless steel can be painted using standard processes and equipment.

Comparison to plastics, composites

Plastics and composites are ideal alternatives to stainless steel in specific applications. Composites offer advantages over stainless steel, including providing a lighter design and easy modification options. However, Fiberglas composites can experience fibre bloom from UV rays, which is a common corrosion mode. A composite enclosure will likely have a lower cost than a stainless steel enclosure. However, in most situations, stainless steel offers better corrosion resistance and strength. Stainless steel is also better suited for extremely high or low operating temperatures.

Stainless steel is not recommended in environments that feature acids, such as hydrochloric and hydrofluoric, or in areas where ferrite chloride is present. In these applications, a polyester enclosure may be the better selection.

While a stainless enclosure is relatively quick to design, build and test, a composite enclosure takes additional time to design. The tooling for a composite design also requires significant time and more costs to develop. If the final composite enclosure is unacceptable or does not pass an aspect of testing, the formulation of the material can be changed, but modifying the tooling may not be possible.

Plastic and composite enclosures are quality insulators, while mild steel and stainless steel absorb and conduct heat better. If an application requires the enclosure to dissipate heat, a mild steel or stainless steel enclosure should be considered.

Summary

Stainless steel offers increased corrosion protection against environmental elements, while also providing a polished appearance and minimal maintenance. With a variety of grades and surface finishes, stainless steel can accommodate diverse application requirements while providing the necessary protection and performance. However, it is important to understand the enclosure environment before selecting stainless steel over other alternatives (painted or plated mild steel, plastics/composites), and also in choosing which grade of stainless steel should be used.


 

This article was first published as a white paper by Pentair. Read the entire document here: www.pentairprotect.com/wcsstore/AuroraStorefrontAssetStore/UserDownloads/WhitePapersCaseStudies/WP-00032_EN.pdf.

 

 

 

Related Articles


Latest Articles

  • Code Question on Section 24 – Patient Care Areas

    Code Question on Section 24 – Patient Care Areas

    July 14, 2025 The rules for the installation of panelboards, circuits, and bonding in Patient Care Area depends on whether the area is designated as either, Basic Care, Intermediate Care or Critical Care. How are these areas defined? Read more on Section 24 — Health care areas Read More…

  • Ontario’s Institutional Component Drives Non-Residential Construction Intentions in May 2025

    Ontario’s Institutional Component Drives Non-Residential Construction Intentions in May 2025

    July 14, 2025 In May, the total value of building permits issued in Canada rose by $1.4 billion (+12.0%) to reach $13.1 billion. The increase in construction intentions was driven by Ontario’s institutional component (+$1.3 billion). On a constant dollar basis (2023=100), the total value of building permits issued in May increased 11.8% from the previous month and was… Read More…

  • Plan Group Partners in Construction of UHN Surgical Tower at Toronto Western Hospital

    Plan Group Partners in Construction of UHN Surgical Tower at Toronto Western Hospital

    July 14, 2025 Plan Group is proud to be a partner in the construction of the UHN Surgical Tower at Toronto Western Hospital. Plan Group will provide work on the project in: Mechanical: Plumbing, HVAC, Controls, Medical GasElectrical: Lighting & Controls, Power Distribution, Emergency Generators, UPSTechnology: Structured Cabling, AV Systems including Digital Signage and IPTV UHN’s 15-storey Surgical… Read More…

  • How Canada Can Equip Workers for a Low-Carbon Future

    How Canada Can Equip Workers for a Low-Carbon Future

    July 14, 2025 The Canadian economy is shifting towards low-carbon industries, and the workforce is shifting with it. New roles are emerging, traditional ones are evolving and the demand for skilled workers is growing fast — particularly in light of the ambitious nation-building agenda the federal government has set out. In the federal Speech from… Read More…


Changing Scene

  • Luxxbox Launches Quick Ship Program to Accelerate Project Timelines

    Luxxbox Launches Quick Ship Program to Accelerate Project Timelines

    July 16, 2025 Luxxbox announces the launch of its new Quick Ship Program, designed to provide architects, designers, and project managers in the United States and Canada with expedited access to a curated selection of their most in-demand acoustic lighting products. With a two-week turnaround from order to dispatch, the program ensures that project timelines… Read More…

  • ECS Earns Platinum Status for 8th Consecutive Year in Canada’s Best Managed Companies Program

    ECS Earns Platinum Status for 8th Consecutive Year in Canada’s Best Managed Companies Program

    July 16, 2025 Electrical Cable Supply (ECS), Canada’s largest independently owned wire and cable distributors, is proud to announce its re-certification with the prestigious Platinum designation in Deloitte’s Canada’s Best Managed Companies program for the eighth consecutive year. This announcement recognizes ECS’s sustained excellence in strategy, innovation, culture, and strong financial performance. The Canada’s Best… Read More…

  • Nexans Canada Partners with Skills Compétences Canada to Sponsor WorldSkills Team Canada 2026

    Nexans Canada Partners with Skills Compétences Canada to Sponsor WorldSkills Team Canada 2026

    July 16, 2025 Nexans has announced its partnership with Skills Compétences Canada (SCC), a not-for-profit organization that actively promotes careers in skilled trades and technologies. As part of the partnership, Nexans will sponsor WorldSkills Team Canada 2026 as they prepare to compete at the 48th WorldSkills Competition, taking place in Shanghai, China, from September 22 to 27, 2026. “At Nexans,… Read More…

  • OEL Apprentice Success Project Available Until March 2026

    OEL Apprentice Success Project Available Until March 2026

    July 14, 2025 With renewed funding by Ontario’s Skills Development Fund, the OEL Apprentice Success Project is now available for another year until March 2026. The project is part of OEL’s Employer Engagement Program (EEP) consisting of wage, training, and equipment subsidies for apprentices. These funding opportunities are available to OEL Members and non-Members. For… Read More…