Avoiding and Resolving Issues with Products That Don’t Dim as Expected

Controls

Sept 16, 2018

With the right combination of dimmer and solid-state driver for LED products, dimming performance can achieve excellent results from 100% all the way to dark, smoothly and predictably. However, when the combination is wrong, many undesirable effects may occur, such as flashing, pulsing, flickering, or fluttering. Part 1 explored some of these behaviours. Here in Part 2, several potential causes and solutions.

At the top of the list is to ensure that the dimmer is properly connected and matches the driver being controlled. Utilizing 0-10V controls on 1-10V drivers can cause issues at low dim settings, specifically when on-off functionality is included. 1-10V luminaires on 0-10V dimmers may flash when turned on/off or will fail to turn off completely without cutting incoming power.

There are also two types of 0-10V dimming: voltage sourcing and current sinking. For entertainment control applications, it is possible that the control will use voltage sourcing, where the dimming system provides the low voltage control signal to the driver. For all architectural controls, current sinking is used, where the luminaires provide the low voltage signal for the control to act upon. Mixing these two up will result in no dimming response at all. Insure that the driver and dimmer are in compliance with IEC60929, which specifies both the voltage and current characteristics of architectural dimming controls. 

Connecting line voltage dimmers demands that the type of dimmer match the driver employed. Triac dimmable products will generally function with Triac (leading edge) or ELV (trailing edge) dimmers, while trailing edge products will exhibit flickering and sudden dimmer responses when connected to Triac dimmers. For the most part, use of LV (designed for magnetic transformer loads) is not recommended, as the dimmer function can be unpredictable. Line voltage dimmers are available from so many providers, with a wide range of specification, causing a range of issues that cannot be described fully here.

As a proactive measure, selecting products that are designed within IEC TR 63036:2016(E) which describes standardized forms of phase cut dimming. The only sure method for assuring compatibility is to test the dimmer with the intended load to expose any undesirable reaction. Driver and luminaire manufacturers may also provide lists of pre-tested dimmers found compatible. For diagnosing field problems, having a known functioning dimmer on hand to install and compare to a product causing field issues can go a long way toward solving an issue quickly. 

Wiring problems are generally diagnosed by disconnecting the dimmer controls and verifying luminaire function at full power. If this resolves undesirable dimming effects, the next step is to test different dimmers on the circuit in order to eliminate dimmer control incompatibility issues. If the problem persists, it will be necessary to remove a sample luminaire and attempt to isolate the driver itself as a cause separate of the dimmer, or compatibility issues with the dimmer. This requires the participation of the manufacturer, to avoid any possible miss-wiring of luminaires that might void warranties or cause failures the manufacturer will not accept as their responsibility.

Luminaire design issues can also become evident when dimmed. Generally, when an LED luminaire flashes, either at start up or at some point when dimmed, the issue can be traced to a low forward voltage condition, where the LED being powered is not producing enough voltage drop for the driver to function properly. Many drivers will flash, or strobe at low frequencies, indicating this condition. Others may simply stop operating at some point when dimmed. This can only be resolved by the luminaire manufacturer, in order to ascertain whether a component within the system is the cause, or some other issue has arisen in manufacturing that was not discovered. It is worth noting that dimming malfunctions due to internal circuit voltage problems are more common with 277V systems than at 120V. Further, during construction, temporary power is often outside the standard voltage specification, which can cause dimming issues that disappear once more reliable permanent power is connected. 

Flickering at either 120Hz or 60Hz is another common dimming complaint. This is most frequently present in low quality line voltage, phase cut dimming controls connected to low cost driver components. This is not a field condition, it is a product issue that should be addressed during product selection phase. 

Fluttering of light levels when a dimmer is moved through its range is often caused by low cost dimmers that have too few steps. Most electronic dimmers utilize some form of digital circuiting that steps light output down from full to minimum dim setting. To avoid this, quality dimmers utilize a large number of sampling steps, that are imperceptible to the operator. Low cost products may use fewer samples, creating a sense of flickering steps as the dimmer is actuated. This can exist in manual dimmers as well as electronic control systems.

Avoiding field issues is the first and best strategy when applying dimming of luminaires. A little effort put into testing samples, verifying compliance with standards, or verifying compatibility with manufacturers is an essential first wall of defence. With this in hand, field problems can then be assumed to be extraneous to the product interaction, leaving field wiring as the first issue to double check. After that, any issues can be boiled down to products not performing to manufacturer standards, which is then used to recruit them into solving field issues experienced. When expectations are realistic, products qualified through specification and/or testing, and installed verified to be complete and correct, there should be no field issues to resolve.

Kevin Willmorth has been involved with lighting since 1981. His experience includes electrical system design, lighting design consulting, product design, marketing, business strategy, and editorial writing. His past positions include positions include owner of a lighting design consultancy, VP of Design and Marketing for Kim, Winona, and Visa Lighting, VP and Director of Product Management Renaissance Lighting, and VP of Design – Lighting for Atlandia Design. He currently owns Lumenique, LLC, offering product design, prototype development, testing, and strategic consulting to manufacturers, application design and technology evaluation for building owners, and Tasca, a small industrial task lighting manufacturing firm. He is also Editor for SSL content in all Construction business media publications including Architectural SSL, Architectural Products, NZB, and Illuminate; kwillmorth@lumenique.com; www.lumenique.com

This article was first published online by the Lighting Controls Association: http://lightingcontrolsassociation.org/2018/07/06/avoiding-and-resolving-issues-with-products-that-dont-dim-as-expected/

Photo courtesy of Eduardo Silva Barbosa on Pixabay

Related Articles


Latest Articles

  • ABB Wins New Product Award at MCEE Show

    ABB Wins New Product Award at MCEE Show

    April 28, 2025 ReliaHome™ Smart Panel won Best New Product Award in the Software, Controls and Related Components category. Iberville® Gangable boxes with low-voltage cables support bracket was recognized as a finalist in the Commercial, Institutional and Industrial Electrical Products category. ABB was honored with a Best New Product Award in the Software, Controls and… Read More…

  • Weidmuller Celebrating a Legacy: 175 Years Globally, 50 Years in Canada

    Weidmuller Celebrating a Legacy: 175 Years Globally, 50 Years in Canada

    April 28, 2025 The year 2025 is truly special for Weidmüller. The company proudly celebrates not just 50 remarkable years in Canada but also its 175th anniversary globally—an extraordinary achievement few companies can claim. This legacy is a testament to the company’s relentless pursuit of innovation and commitment to refining its offerings. But the journey… Read More…

  • Canada Stands Tall at Hannover Messe 2025

    Canada Stands Tall at Hannover Messe 2025

    April 28, 2025 By Owen Hurst At Hannover Messe earlier this month Canada had a strong presence as the host country with a wide variety of companies and programs focusing on the development of advance technology. The presence was accentuated by numerous halls hosting Canada pavilions. Partner Country Canada presented itself impressively at HANNOVER MESSE…. Read More…

  • BC Prompt Payment Legislation Progressing

    BC Prompt Payment Legislation Progressing

    April 28, 2025 Consistent with its mandate of growing the economy, the government wants to ensure that businesses are paid promptly for work performed on (or material provided to) construction projects. British Columbia’s Ministry of Attorney General staff have been tracking the issue of payment delay in the construction industry, including legislative responses in other… Read More…


Changing Scene

  • Schneider Electric Advances in Product Environmental Data Transparency

    Schneider Electric Advances in Product Environmental Data Transparency

    April 28, 2025 Schneider Electric has launched its Environmental Data Program. This initiative, which builds on the legacy Green Premium label, provides customers with unique access to information on the environmental impact of its products, enabling them to make better informed, data-based decisions and meet evolving regulatory requirements with confidence. Schneider Electric has frequently been recognized… Read More…

  • nVent Sustainability Report Highlights Progress and Focus on Electrification

    nVent Sustainability Report Highlights Progress and Focus on Electrification

    April 15, 2025 nVent Electric plc announced the release of its 2024 Sustainability Report. The new report highlights nVent’s achievements in each of its sustainability focus areas: People, Products, Planet and Governance. The report also highlights how nVent solutions support electrification, digitalization and sustainability efforts around the world. “nVent is becoming a more focused electrical… Read More…

  • Ontario Introduces Legistlation to Unlock Trade and Labour Mobility Within Canada

    Ontario Introduces Legistlation to Unlock Trade and Labour Mobility Within Canada

    April 18, 2025 As a next step in its plan to protect Ontario by unleashing the province’s economy, the Ontario government is introducing the Protect Ontario through Free Trade within Canada Act to unlock free trade and labour mobility within Canada. This legislation will, if passed, create new opportunities for job creation and investment attraction, supporting economic… Read More…

  • Ontario, P.E.I. Join Nova Scotia With Legislation to Remove Internal Trade Barriers

    Ontario, P.E.I. Join Nova Scotia With Legislation to Remove Internal Trade Barriers

    April 18, 2025 Prince Edward Island and Ontario have joined the Nova Scotia by introducing reciprocal legislation that will help foster an environment of mutual recognition of goods, services and labour mobility between these provinces. “Leaders across the country are expressing interest in removing trade barriers, and I’m very pleased that P.E.I. and Ontario have… Read More…