Power Factor Correction: An Overlooked but Powerful Tool for Delivering Energy Efficiency and Savings

August 23, 2016

Joy Silber

Amid all the talk about how to reduce CO2 emissions and limit climate change, renewable energy sources such as wind and solar often take centre stage. But there’s another technology poised to deliver energy reductions of 10% or more that gets far less attention: power factor correction (PFC).

If you’re not familiar with PFC, you are far from alone. To date, it’s been a largely overlooked method of reducing energy consumption, costs and CO2emissions, and achieving sustainability. But PFC is actually far more effective than many “green” alternatives because it effectively enables companies to get more power out of the same amount of utility electricity.

Understanding power factor

I won’t kid you: PFC is a bit complicated to explain and understand, making a full discussion of it beyond the scope of this post. You can learn all about it from this free Schneider Electric paper titled Energy efficiency improvement through optimization of the power factor correction.

But the basic concept is it takes more energy to power a given load than the actual power that the load consumes. That’s because some of the energy is lost in translation, so to speak. Power factor is used to determine just how much more energy will be required to power the load. This amount is measured by calculating a ratio that shows how efficient any given machine is. A motor with a power factor of .90, for example, is 90% efficient. To determine how much energy you’ll need in kVA to power that machine, you perform an equation: 100 (for a 100kW motor) ÷ 0.90 = 111kVA. So you’ll need 111kVA of utility power to run that 100kW motor.

Saving energy with power factor correction

Obviously, the lower your power factor of a given piece of equipment, the less efficient it’s going to run. And that inefficiency can cost you more than just a higher utility bill because in some areas, you’ll get penalized for consuming more power than your contract allows, taking into account your power factor.

The key to ensuring that doesn’t happen is to use a capacitor bank or energy compensator. These systems perform PFC to help reduce the amount of power an AC device has to consume to generate its rated amount of power. Some systems, such as Schneider Electric’s VarSet low-voltage capacitor banks, automatically correct power factor. This results in a power factor close to 1, meaning virtually no power is wasted.

Using PFC systems can deliver a number of benefits, including:

• significant savings on electricity bills, with ROI typically within two years (actual savings vary depending on local utility penalties)

• improved energy efficiency

• attained sustainability goals

• reduced energy use waste

• increased available power at your facility

• reduced carbon footprint

• Improved equipment reliability and lifespan by filtering “dirty power”

Sounds an awful lot like many of the same benefits that solar and wind deliver, doesn’t it? The savings can indeed be impressive, and they’re relatively simple to achieve. To learn more about power factor correction in your facility, email:powersolutions@schneider-electric.com


Joy Silber is the Strategic Marketing & Sales Optimization Manager of Power Solutions at Schneider Electric. With experience across multiple industries: Food and Beverage, Mechanical, Agriculture and Power Transmission, Joy has held previous roles in National Sales Development, Market Segment Management, Marketing Services Management and Business Development. She has a B.S. from North Carolina State University and is an active volunteer in her community. This article was first published as a blog.

 

 

 

Related Articles


Latest Articles


Changing Scene

  • Have your Say on the Proposed Regulations for the NWT Builders’ Lien Act

    Have your Say on the Proposed Regulations for the NWT Builders’ Lien Act

    February 14, 2025 The GNWT is modernizing the legal framework for construction liens. In 2023, the Builders’ Lien Act was enacted to replace the Mechanics Lien Act. The new legislation was put in place to address modern construction practices. It sets out the legal processes, systems, rights, and remedies for parties involved in construction disputes.  The GNWT… Read More…

  • Federal Government Investing in Skilled Trades Training for Atlantic Canada

    Federal Government Investing in Skilled Trades Training for Atlantic Canada

    February 14, 2025 Canada is building more homes, bridges and key infrastructure than at any point in recent history. That requires skilled workers in communities across the country, including in the Atlantic provinces. To encourage more people to join the skilled trades, to build the homes Canadians expect and the resilient economy this moment demands,… Read More…

  • Nova Scotia Power Holding Open Houses to Discuss Modernizing the Electrical Inspections Process

    Nova Scotia Power Holding Open Houses to Discuss Modernizing the Electrical Inspections Process

    February 14, 2025 As Nova Scotia continues to experience unprecedented building growth, it’s the perfect time to review and improve the electrical inspection process—with safety as the top priority. Nova Scotia Power and the Department of Labour, Skills, and Immigration are coming together to explore new opportunities—including risk-based electrical inspections—to ensure the process remains safe,… Read More…

  • Alberta EV Tax Begins February 13th

    Alberta EV Tax Begins February 13th

    February 14, 2025 Starting Thursday, Feb. 13, Albertans will be charged a $200 tax when they register their electric vehicles. This amount is in line with what drivers of a typical internal combustion engine vehicle would be expected to pay each year in fuel tax. The tax will be collected by registry agents, and online… Read More…